to the
Connecting the Cables
CD-Rom
Warning/Caution
Introduction
Safety Precautions
The following are basic precautions to ensure user safety
and reduce the risk of property damage.
Warning: To warn the user that failure to comply with the instructions may result in
CD-ROM DRIVE
SH-152
serious injury or death.
Caution:
To caution the user that failure to comply with the instructions may result in
damage to property.
Design and specifications are subject to change without prior notice.
Connecting the Cables
Eject Button
When you install the drive
Place the drive on a level
surface.
Failure to do so may cause the
device to fall onto a hard surface,
resulting in damage or malfunction.
Power cable
Avoid low - or high-temperature
environments.
Avoid high-humidity environments.
Do not place the drive in
direct sunlight.
Front
User's Guide - ENGLISH
EIDE cable
Master/slave select terminal
Audio cable
FCC Compliance
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
Disc compartment
LED
Emergency eject hole
While operating
If the compartment does not open
when you press the Eject button,
power off the computer, insert a pin
or unfolded paper clip in the hole
and push firmlhy)
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Do not move the drive while in operation
and do not attempt to open the disc tray
byforce. Make sure to close all working
programs before attempting to open the tray
and always use the open/close button.
Do not use cracked, distorted or
damaged discs.
Do not drop the drive, and protect it
fromsevere shocks.
Handle with caution to prevent
damage from external shock.
Connecting the power cable
1
2
The 4-pin power cable from the internal power unit of your computer must
be connected to the power terminal the rear of the CD-ROM drive.
It can damage the drive or cause
it to malfunction.
Connecting the EIDE cable
Interface terminal
Sound output terminal
Insert the EIDE cable (40-pin), which is connected to the hard
disk to the interface terminal.
In particular, a disc with a crack on the
inner tracks may break while in use.
Do not insert a pin into the emergency
opening while in operation.
• Re-orient or relocate the receiving antenna.
(Place the red line of the cable close to the Pin 1.)
• Increase the separation between the equipment and receiver.
Installing a jumper on the master/slave select terminal
3
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Rear
Other
Connect a jumper to the rear side of the CD-ROM.
If the jumper is connected to MA (Master), it will work in the Master mode.
If the jumper is connected to SL (Slave), it will work in the Slave mode.
If the jumper is connected to CS (CSEL), you can control the device by using the
host interface signal CSEL. (In general, connection to MA is recommended.)
Important to read and understand
at all times
Do not disassemble, attempt to repair or
modify the device without express
approval as directed in the manual.
To reduce the risk of damage,
electric shock, and fire.
• Consult the dealer or an experienced radio/TV technician for help.
Never allow food particles or
foreign substances to enter the
drive casing.
To protect against the risk of
fire, do ot spill such liquids as
alcohol and benzene on the
drive.
CAUTION
Change or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate
the equipment.
Do not disassemble
CS : Cable Select(CSEL)
SL : Slave
MA: Master
Digital output Master/slave select terminal Power terminal
terminal
LASER STANDARD
IEC 60825-1 : 1993 + A1 : 1997 + A2 : 2001
Accessories
EIDE cable, 4 screws.
Connecting the audio cable from a sound card
Connect the 4-pin audio cable between the sound output terminal on the
CD-ROM drive and the audio input terminal on the sound card.
1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole),
it is recommended that you make a copy immediately and use the copy instead. When a cracked disc is used continuously,
the size of the crack is likely to grow and it will eventually result in irreparable damage to the disc.
2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs).
Any change or modification not expressly approved by designated qualified personnel could
void your authority to operate this device.
4
Design and specifications are subject to change without prior notice.
BG68-00787A Rev.01
1
3
2
4
Using the Drive/Storing and Cleaning
Solving Technical Problems
Installing the Drive
Technical Specifications
Your Discs
The friction noise generated during SPIN-UP and STOP is caused by the
Automatic Ball Balancing System(ABS) and is not a malfunction.
When using one EIDE cable
System Requirements
Intel Pentium 166MHz(or higher), 16 MB of RAM (or higher) with an EIDE
Using the CD-ROM Drive
SECTIONS
SH-152
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear
of the CD-ROM drive.
Check that the power, audio and EIDE cables are correctly
connected to the computer.
CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,
Form-2, Photo-CD(Single, Multi-session), Video CD ready,
CD-Plus, CD-Extra, Enhanced CD, CD-I/FMV, CD-R/RW
The CD-ROM drive is not
detected by the computer.
Push the power button and boot the computer.
interface, Windows 98 / 2000 / ME / XP Windows NT 4.0 (or higher)
Disc types supported
1
DISC
Change the EIDE cable and reconnect it to the computer.
Preferably, connect a second EIDE cable to the CD-ROM drive
in master mode.
Slave Drive (Choose the SL Jumper)
Installing the CD-Rom Drive
Disc diameter
120mm or 80mm
52X, 7800KB/s(MAX)
PIO Mode 4, DMA MW2, UDMA2
90ms(typical)
After booting the computer, open the disc
2
After installing the CD-ROM
drive, the PC gets slower.
How to install the CD-ROM drive on your PC. First, remove the cover;
connect the cable to the CD-ROM drive and then to the PC.
compartment by pressing the Eject button.
Data transfer rate
Check the position of the jumper in the master/slave select
terminal.
Insert the disc (CD) with the label on the disc
Access time (typical
Data buffer capacity
Laser
)
3
128KB
DRIVE PER -
FORMANCE
facing upwards and close the disc compartment
The CD-ROM drive is not
recognized by MS-DOS.
Reinstall the device driver or update it with the latest version by
downloading it from the Samsung Web site.
If necessary, attach a horizontal bracket
Semiconductor laser
Step Motor
MainBoard
Hard Drive
1
by pressing the Eject button. The indicator light
to both sides of the drive.
Slide mechanism
Spindle motor
comes on.
Play the disc (CD).
Brushless motor
You can purchase these accessories separately
from your computer dealer.
When using two EIDE cable
Tray, DC motor(Soft Eject)
Mode-1 : 1block / 1012 bits, Mode-2 : 1 block/10 9 bits
Load mechanism
The CD-ROM drive is not
detected by Windows.
This case may occur when there is a Windows installation
problem; reinstall Windows.
4
Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear
of the CD-ROM drive.
ERROR RATE
(Screws for use: M3 X 6 X 4)
Playing CD-DA/Audio CDs
Run the CD player program supplied with the sound card or play the
Windows Media Player.
FRONT
PANEL
Eject button
Auto eject or Auto inject
Check whether the audio cable is correctly connected to the sound
output terminal on the CD-ROM drive and the sound card CD-IN
terminal.
No sound is heard from an
audio CD.
- If there is only one Optical drive: select MA (Master).
Indicator(LED)
POWER ON/BUSY
Required power
Interface connector
Audio output
+5V DC 1.3A, +12V DC 1.5A
ATAPI
Master Drive (Choose the MA Jumper)
Check that the sound card is operational.
Playing Video CDs
REAR PANEL
Line out 0.70 20%(Vrms), 47kΩ
Follow the instructions provided with the disc.
A video card or MPEG software and a sound card need to be installed to view video CDs.
SEC 1
PRI 1
Check whether the CD is of good quality and clean it,
if necessary.
A CD is not read or is read
too slowly.
Jumper block
Molex 70203 or other compatible models
Temperature : 5~45 °C, Humidity : 10~80%
Remove the plate from a free expansion slot and install the
Work area
Storage area
Dimensions
Net weight
MTBF
If the drive is vertically installed, you cannot use an 8 cm MiniDisc because the disc is
movable.
OPERATING
ENVIRONMENT
2
The disc compartment will
not open.
Check that the power cable is correctly connected.
Power off and disconnect the PC.
CD-ROM drive, as shown in the illustration.
Temperature : -25~60 °C, Humidity : 10~90%
MainBoard
Hard Drive
If you have no free expansion slot, install the drive in place of the
diskette drive.
148.2 (W) x 42(H) x 184(D)mm
740g (set only)
Insert a pin or unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
Storing Your Discs
Do not place a disc in direct sunlight.
Store a disc vertically in a well-ventilated and
stable location.
Do not write or attach a label on a disc.
Do not drop a disc or place heavy objects on it.
General
-If there is two Optical drive, select MA (Master) / SL (Slave).
Make sure to use the standardized screws supplied (M3X6).
- To use screws other than M3X6 may result in malfunction.
125,000 POH (Duty 20%)
reliability
Master Drive (Choose the MA Jumper)
Slave Drive (Choose the SL Jumper)
When the MPEG software
plays a Video CD, the pictures
are not regular and the running
speed is too slow.
Adjust the size of the replay screen.
After checking the display resolution, adjust it, if necessary.
SEC 1
PRI 1
The Disc is not in message is
displayed even though a disc
has been inserted.
The computer may not recognize the disc if you start playback
too quickly after inserting the disc.
Cleaning Your Discs
(Choose the SL Jumper)
(Choose the MA Jumper)
CD-Rom
Drive
Horizontal
Bracket
Plate
Hard Drive
Open and close the disc compartment and try again.
Clean the disc and try again.
Do not touch the surface
of a disc; hold it by the
edges.
To clean a disc, polish lightly
from the inside of the disc to the
outside with a soft cotton cloth.
MainBoard
The CD-ROM drive is not
detected after it is connected
to a sound card.
The interface mode of the sound card is AT-BUS.
You must therefore connect the CD-ROM drive to the EIDE
port on the PC mother board, rather than to the sound card,
or install an EIDE compatible sound card.
The disc may not function properly if there are fingerprints, foreign substances or
dust on the disc surface.
9
8
7
6
5
|